Kommentare

Anmelden zu kommentieren.

1. figtree7nts🇺🇸

   Admiral·vor 4 Jahren

   I spent a few days trying to figure out how to fix my botched-up Mast!
   
   As the lighting wasn't correct and Albert90 was kind enough to let me know it was Botched up!
   
   Thanks, Albert90 it's now fixed!
   
   Anyway,
   
   I ended up pulling the old led's from the aft of the Mast!
   
   I then had to somehow drill tiny little holes to run the wires from the new led's!
   
   I carefully did everything without breaking the Mast!
   
   It was a real challenge to do this repair!
   
   This is what I ended up with!
   
   Repairs all done- 👍
2. figtree7nts🇺🇸

   Admiral·vor 4 Jahren

   Hi Marky,
   
   Thank you, it's good to be back!
   
   And building a nice big boat!
   
   Cheers,
   
   Ed-

   Gefällt von Martin555
3. figtree7nts🇺🇸

   Admiral·vor 4 Jahren

   Hi Albert90,
   
   I see what you mean about the lights!
   
   As I was building the Mast, I didn't have any reference to her lights!
   
   Someday I'll fix that mistake!
   
   But, for now all I can say is Oop's! LOL!
   
   Thanks for noticing!
   
   Cheers,
   
   Ed-

   Gefällt von Martin555 and Albert90 Alle ansehen
4. marky🇬🇧

   Kommodore·vor 4 Jahren

   Really nice build Ed , glad to see you back all the best .
   Cheers Marky👍

   Gefällt von figtree7nts and Martin555 Alle ansehen
5. Albert90🇳🇱

   Petty Officer 1st Class·vor 4 Jahren

   Hello Ed, I’m also building this tug.
   I think one thing with the lights is wrong. the white red white light at the rear of the mast means: limited maneuverability, and is red white red. But very good looking built model,👍

   Gefällt von Mike Stoney and figtree7nts Alle ansehen
6. Martin555🇬🇧

   Flottenadmiral·vor 4 Jahren

   Ed And Peter,
   I think the red LED draws more current, so if the same value resister is used in both cases then the Green will be brighter than the Red.
   
   I am not an electrical wizard so maybe other members could explain the reason why this could be happening.
   
   Martin.

   Gefällt von Len1
7. MouldBuilder🇭🇺

   Admiral·vor 4 Jahren

   Hi Ed.
   Red never seems as bright. What is the supply voltage.
   Peter.😊

   Gefällt von Martin555
8. figtree7nts🇺🇸

   Admiral·vor 4 Jahren

   Hi Peter,
   
   It's 5 volts for all my LEDs with a resister that was supplied by the Manufacturer!
   
   I haven't a clue as to its rating! LOL!
   
   But I believe I did it correctly because I haven't blown myself up! TeHe😂🤣👍
   
   But these LEDs are bright!
   
   My port is a bit dimmer than my starboard side!
   
   Cheers,
   
   Ed-

   Gefällt von Martin555 and Colin H and 1 other
9. MouldBuilder🇭🇺

   Admiral·vor 4 Jahren

   What voltage is being supplied and what value is the resistor?🤔

   Gefällt von figtree7nts and Martin555 Alle ansehen
10. figtree7nts🇺🇸

    Admiral·vor 4 Jahren

    Hi Peter,
    
    I know it looks really bright!
    
    Not sure why that is though?
    
    I'll take a look to see if it's too bright maybe I can place a higher who Resister?
    
    Maybe?
    
    Cheers,
    
    Ed-

    Gefällt von Martin555 and MouldBuilder Alle ansehen